eCigs, Mods, Batteries and Safe Vaping
2024-06-13
eCigs, Mods, Batteries and Safe Vaping
Intermediate
eCigs, Mods, Batteries and Safe Vaping
While eCigarettes and personal vaporizors have been used billions of times without issue, they do involve batteries- which are not all the same. Using the incorrect battery or damaged battery in a PV can stress the battery cell into venting, and possible explosion. With the use of “mods” or devices that can use a variety of batteries, the possibility of using an incorrect battery could be more probable. This article applies to mods, or PV’s that do not use your standard ecig “stick” battery.
Knowing a few key points about mods, battery ratings and “what if” is a good thing. With the right device, a GOOD battery charger and the correct battery- you should have little to worry about when vaping.
Battery rating, volts, ohms and safety
Devices have different requirements when it comes to battery rating. Always follow manufacturer instructions. If it says only use IMR batteries- take the warning seriously.
Use Li-Mn cells, or protected Li-ion cells. (AW brand IMR has great ratings)
Make sure the C rating on your battery is at least 2 amps (2,000mA)
Don’t overcharge. Even if your charger has protection against overcharging- it could fail.
Stacking batteries- The warning: Stacking batteries is not suggested- and hugely warned against. Stacking improper batteries can place a strain on the battery cell and cause venting and/or explosion. When stacking batteries, the risk goes up.
If you decide to ignore the above warning, do NOT ignore the following tips:
Never stack an old and new battery together
Never use a damaged battery
Test your batteries after charge to make sure they aren’t overcharged
Test your batteries after charge and then a rest for a couple days. Make sure they are holding the charge.
Always use a protected battery
High drain devices should use an IMR battery
Safety Features in your mod–
Some mods will have proper venting built in as a safety feature. A lot of mods use a collapsible spring that will prevent the battery from coming in further contact with its ground. Some mods design a “weak spot” such as weaker end cap threads, or door.
More battery information:
Current advice (from ECF)
The following advice can be given at this time:
For ultimate safety, use a single-battery mod.
For high-voltage, use a single-battery mod with a booster circuit of some kind.
Use the best and most expensive battery you can get. It doesn’t seem worth it to economise on batteries. Our opinion is that, at this time, the AW IMR ‘red’ cell has the best reputation. It is a lithium-managanese ‘safe chemistry’ cell that does not need the integral protection circuit a Li-ion cell needs. Although these have never been known to explode, no lithium battery, ultimately, is absolutely safe: they will certainly meltdown with plenty of heat and flame if abused; and if they were sealed into a perfectly gastight container, and then made to fail, an explosion might result under those particular conditions.
We know that using a two-battery metal tube mod is intrinsically more dangerous because these are where the explosions are.
Using such a mod with no proper gas vents and no bottom-end blowout plug seems to involve the highest risk.
You should think very carefully before buying a metal tube mod with no
physical safety features.
Mods need safety features because nobody really knows what battery they have, you just assume it is what it says on the label. But there are a whole lot more Gucci handbags out there than the factory ever made. Lots of people think they have a Gucci handbag but they don’t. So, you may think you have two AW cells, but they could be cheap clones with counterfeit labels. And they might not even be Li-Mn cells: they might just be unprotected Li-ion cells.
Mods need safety features because users make mistakes. Everybody makes mistakes. If your safety depends on never making a mistake, then you are not safe.
Mods need safety features because the battery condition may be faulty but not have been noticed. Some mod owners don’t even own a meter, so we know this is going to happen in some cases.
Mods need
physical safety features because electronic ones might fail. That’s what electronics does. And according to the most basic law of engineering, it will fail at the worst time in the worst way and in a chain of failures. People who say it can’t happen aren’t engineers and should not be building consumer products to be used in front of the face.
You should think very carefully before buying the cheapest batteries you can get, then stacking them. Especially in a metal tube mod. And especially in one short on safety features.
Batteries all have a C Rating.
Don’t use batteries with a C Rating below 2 amps (2,000mA) as they
ARE NOT up to the job.
Bigger batteries are safer because they can handle the heavy load an atomizer puts on them. No big battery (i.e. an 18500 or larger) has ever exploded.
All batteries can meltdown and cause a fire if faulty and/or abused.
DON’T put a mod in your pocket or purse with the atomizer connected or the master switch (if fitted) on; or along with keys and change.
Adapters can be treacherous, so be careful – they can short out.
ECF Thread on battery safety
